TUNED "Vortexed" DRAG PIPE & MOTOR MOUNTS for OCC / Spoiler Stingrays


XL "vortexed" Drag Pipe
XL "vortexed" Drag Pipe

YOU MUST HAVE:

An OFFSET Motor Mount & Drag Style Pipe (as shown in photo right) to mount a Chinese 2 Stroke onto an OCC Schwinn Stingray.  The on-line Motor kits do not come with the proper pipe and mount for installing motors on this style bike.

 


STANDARD or XL Length "Vortexed" Drag Pipe

STANDARD  or XL length Pipe - click on arrow and find drop down box for pricing.  play youtube video below to hear this pipe on an engine that is running.

$109.99

  • 4 lb
  • Available
  • Ships within 1-3 days1

PRECISION MACHINED / STINGRAY SPECIFIC MOTOR MOUNT

INSTALLATION IS NOW A SNAP!

 

ATTN: DESIGNED FOR SMALLER  1 1/2" inch  MOUTH [FRONT MOUNT] STUD WIDTH.  If you have 2" inch STUD WIDTH on your motor...  YOU WILL ALSO NEED ADAPTOR IN [BOX JUST BELOW].

 

HOLDS YOUR MOTOR AT THE EXACT ANGLE & OFFSET for optimal chain alignment...  Machined from Aluminum Billet.  Allows for several inches of [forward or backward <-> slide] to make drive chain and bicycle side chain "match up" much faster and easier...

 

Includes: All stainless steel mounting hardware. Also, grade 12.9 [hardest metric bolts] for attaching motor to mounts.

Note: I charge a little extra shipping on these as it takes a considerable amount of time to prep. and mounts include 24 stainless steel bolts per set. 

 

 

$99.99

  • 3 lb
  • Available
  • Ships within 1-3 days1

SPOILER STINGRAY - MACHINED MOUNT

Our Precision Machined Motor Mount - DOES IN FACT WORK with the Stingray "SPOILER" Model!  with the insertion of an additional spacer to REAR MOUNT.   And also - Our NEW Jackshaft Component matches up to spoiler [OVAL] shaped tubing.   It turns out that Both the OCC style Stingray and Stingray Spoiler's Lower frame tubing is same size and shape.

$119.99

  • 3 lb
  • Available
  • Ships within 1-3 days1

MOTOR MOUNT "ADAPTOR"

[ADAPTOR OMLY] Small rectangular machined fittings in [PHOTO - IN FRONT OF MOTOR]   These Adaptors allow you to adapt our Stingray Specific machined motor mount to fit the WIDER MOUTH Motors.  Check the measurement on the front STUDS ON YOUR MOTOR....  If the measurement is around 1 1/2 inches [center to center ] of bolt holes or studs NO ADAPTOR NEEDED.  If measurementis 2 inches - you will need our 2 inch adaptor.  If you have a NEW Grubee GT5A or similar and the measurement is 2 1/2 inches = you will need our 2 1/2 inch adaptor....  comes with needed hardened mounting bolts.

$19.99

  • 2 lb
  • Available
  • Ships within 1-3 days1

NO DRILL / STEEL OFFSET MOTOR MOUNT

JUST UPGRADED - To a heavier [thicker] American made / Steel Off-Set Mount.  [Photo - looks the same but americn mount is thicker steel] ..  You must have an offset mount to mount a Chinese 2 stroke motor onto an OCC style Schwinn Stingray frame. Includes: mount, motor mounting hardware, mount hardware.  And... A thin 1/8 inch - Non - slip neoprene  pad inserted between mount and frame.  Also spacers - to push motor away from left side crank arm.

 

NOTE: Front of mount is to the right in this photo.  There are holes [top right] for center mount - not used on stingray...  If your motor front mounting studs are wider than what is pre-drilled in mount...  You will have to drill hole to accommadate your [super wide mount] motor.

 

 

 

$65.99

  • 3 lb
  • Available
  • Ships within 1-3 days1

MOTOR MOUNT [REAR] SUPPORT BLOCK

Heavy Duty - SUPPORT BLOCK

REAR SUPPORT BL0CK ONLY - RECTANGULAR  ONLY - arched no longer available.  

Replace your factory support with our...    NEW PedalChopper EDITION: HEAVY DUTY [solid aircraft aluminum] Motor Support Block.

  

Rectangular BLOCK for Flat Bar [No Drill} style motor Mount

 

$19.99

  • 2 lb
  • Available
  • Ships within 1-3 days1

SCHWINN STINGRAY SPOILER MOTOR MOUNT...  Recently, found out that our Precision Machined Motor Mount - DOES IN FACT WORK with the Stingray "SPOILER" Model!  And also - Our NEW Jackshaft Component will also match up to spoiler [OVAL] shaped tubing.   It turns out that Both the OCC style Stingray and Stingray Spoiler's Lower frame tubing is same size.


                                Watch the video!


FINNED EXHAUST HEADER WORKS GREAT WITH THIS PIPE!

FINNED EXHAUST HEADER

IMPROVES FLOW & COOLING!  AND LOOKS GREAT!

 

Notice champhered edges - allows easy mounting on all motors as top edge fits nicely below fins of cylinder head without touching / bumping into them.

 

INCLUDES: ONE (1) Finned Exhaust Header, TWO (2) High Quality Grubee Exhaust gaskets and Mounting Hardware.

$27.99

  • 2 lb
  • Available
  • Ships within 1-3 days1

Questions - fill in the form below or  contact us directly through sales@pedalchopper.com

Note: Please fill out the fields marked with an asterisk.